;-------------------------------------------------------------------------- ; ; ; PEEDI sample target configuration file ; ; Ronetix ; ; Supported devices : Atmel AT91R4008 ; Board : Atmel AT91EB40A ; ; Revision : 1.0 ; ; Date : Dec 29, 2008 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2010, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE=eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = ARM [PLATFORM_ARM] JTAG_CHAIN = 4 ; list of IR lenghts of all TAP controller in JTAG chain JTAG_CLOCK = 5, 16000 ; JTAG Clock in [kHz] - 5kHz jtag clock for init operations and 16MHz for normal work TRST_TYPE = PUSHPULL ; type of TRST output: OPENDRAIN or PUSHPULL RESET_TIME = 20 ; lenght of RESET pulse in ms; 0 means no RESET TIME_AFTER_RESET = 500 CORE0 = ARM7TDMI, 0 ; TAP 0 is ARM7TDMI CPU CORE0_STARTUP_MODE = RESET ; startup mode after reset: ; if RESET than no code is executed after reset ; if STOP,XX then the target executes code for XX period in ms. ; if RUN then the target executes code until stopped by the telnet "halt" command CORE0_BREAKMODE = soft ; default breakpoint mode for the debugger: ; soft - use software breakpoints ; hard - use hardware breakpoints CORE0_INIT = INIT_R4008 ; init section CORE0_FLASH0 = U-BOOT CORE0_ENDIAN = little CORE0_WORKSPACE_ADDR = 0x00000100; start address of workspace for flash programmer CORE0_WORKSPACE_LEN = 0x10000 ; length of workspace in bytes ; Default path to be used if only a file name (without the full path) is ; provided to a PEEDI command or for the FILE parameter in the Flash sections ; Examples: ; In a console: ; "flash prog tftp://192.168.3.1/image.elf" ; is equal to ; "flash prog image.elf" ; ; In a Flash Profile: ; FILE="tftp://192.168.3.1/image.bin", BIN, 0 ; is equal to ; FILE="image.bin", BIN, 0 ; CORE0_PATH = "tftp://192.168.3.1" ;CORE0_PATH = "card://" CORE0_FILE = "test.bin", BIN, 0x20000000 ;------------------------------------------------- ; Init for AT91R4008 ;------------------------------------------------- [INIT_R4008] set cpsr 0x000000D3 mem write 0xFFFF8000 0x2340 ; disable watchdog mem write 0xFFE00024 0x00000006 ; enable A0..A20 mem write 0xFFE00000 0x01002539 ; Flash at 0x01000000 mem write 0xFFFFF124 0xFFFFFFFF ; disable all interrupts ; remap mem write 0xFFE00020 0x00000001 ; remap command [U-BOOT] CHIP = AT29LV1024 ACCESS_METHOD = AGENT CHECK_ID = YES CHIP_WIDTH = 16 CHIP_COUNT = 1 BASE_ADDR = 0x01000000 FILE = "u-boot.bin", BIN, 0x01000000 AUTO_ERASE = YES [SERIAL] BAUD=115200 STOP_BITS=1 PARITY=NONE TCP_PORT = 0 ; enable CLI over RS232 ;TCP_PORT = 2023 ; enable serial over TCP/IP [TELNET] PROMPT = "R4008> " ; telnet prompt ;BACKSPACE=127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 25 ; beeper volume [ACTIONS] ; user defined scripts ;AUTORUN = 2 ; executed on every target connect 1 = erase 2 = prog 3 = dump_ram 4 = dump_flash [erase] ; erase flash flash erase [prog] ; program flash flash prog [dump_ram] ; dump part of RAM memory dump 0x20000000 0x01000 tftp:ram.bin