;-------------------------------------------------------------------------- ; ; ; PEEDI target configuration file for TI TMS470 microcontroller ; ; Ronetix ; ; Supported devices : TMS470 with AWD (Analog WatchDog) enabled ; ; Revision : 1.1 ; ; Date : April 11, 2011 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2010, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE=eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = ARM ; platform is ARM [PLATFORM_ARM] JTAG_CHAIN = 4 ; list of IR length of all ; TAP controller in JTAG chain JTAG_CLOCK = 10, 16000 ; JTAG Clock in [kHz] - 10kHz ; JTAG clock for init operations and ; 16MHz for normal work TRST_TYPE = PUSHPULL ; type of TRST output: OPENDRAIN ; or PUSHPULL RESET_TIME = 20 TIME_AFTER_RESET = 200 PERIODIC_TASK = RESET_WATCHDOG, 100 CORE0 = ARM7TDMI ; TAP is ARM7TDMI CPU CORE0_STARTUP_MODE = RESET ; Let the core enable the JTAG port CORE0_BREAK_PATTERN = 0xDFFFDFFF ; software breakpoint pattern CORE0_BREAKMODE = soft ; breakpoint mode: ; soft - use software breakpoints ; hard - use hardware breakpoints CORE0_INIT = INIT_TMS470A ; init section for TMS470A board CORE0_FLASH = FLASH_TMS470 ; FLASH section parameters CORE0_ENDIAN = BIG ; TMS470 works in BIG endian CORE0_WORKSPACE_ADDR= 0x00800000 ; start address of workspace for flash ; programmer CORE0_WORKSPACE_LEN = 0x3000 ; length of workspace in bytes CORE0_FILE = "myfile.bin", BIN, 0x00400000 ; default file CORE0_PATH = "tftp://192.168.3.1" ; default path [INIT_TMS470A] ; disable illegal address reset memory write 0xFFFFFFE0 0x00004007 ; SYSECR ; set memory select 0 block size to 512kB memory write 0xFFFFFE00 0x00000000 ; MFBAHR0 memory write 0xFFFFFE04 0x000000A0 ; MFBALR0 ; activate RAM at 0x00300000 32k that is connected to memory select 2 memory write 0xFFFFFE10 0x00000080 ; MFBAHR2 memory write 0xFFFFFE14 0x00000050 ; MFBALR2 ; activate new mapping by writing 1 to MFBALR0.8 memory write 0xFFFFFE04 0x000001A0 ; MFBALR0 memory write 0xFFFFFFDC 0x0000000B ; GCR SYSCLK *4 and /4 = SYSCLK /1 [RESET_WATCHDOG] mem write 0xFFFFFF0C 0xE5 mem write 0xFFFFFF0C 0xA3 [FLASH_TMS470] CHIP = TMS470 BASE_ADDR = 0 ACCESS_METHOD = AGENT ;AUTO/AGENT/DIRECT CPU_CLOCK = 12000 PROTECTION_KEY0 = 0xFFFFFFFF PROTECTION_KEY1 = 0xFFFFFFFF PROTECTION_KEY2 = 0xFFFFFFFF PROTECTION_KEY3 = 0xFFFFFFFF ALLOW_ZERO_KEYS = NO FILE = "myfile.bin", BIN, 0 ; file to program AUTO_ERASE = NO ; erase before program [SERIAL] ; serial port configuration BAUD = 115200 STOP_BITS = 1 PARITY = NONE TCP_PORT = 0 ; CLI over RS232 ;TCP_PORT = 2023 [TELNET] PROMPT = "tms470> " ; telnet prompt ;BACKSPACE = 127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 50 ; beeper volume [ACTIONS] ; user defined scripts ;AUTORUN = 2 ; executed on every target connect 1 = erase 2 = prog 3 = dump_ram 4 = dump_flash [erase] ; erase flash flash erase [prog] ; program flash flash prog flash verify