;-------------------------------------------------------------------------- ; ; ; PEEDI sample target configuration file ; ; Ronetix ; ; Supported devices : Freescale iMX25 ; Board : ; ; Revision : 1.0 ; ; Date : Feb 12, 2009 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2010, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE=eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = ARM ; platform is ARM9 [PLATFORM_ARM] JTAG_CHAIN = 5,4,4,4 ; list of IR lenght of all TAP controllers in JTAG chain JTAG_CLOCK = 10, 10000 ; JTAG Clock in [kHz] - 10kHz jtag clock for init operations and 10MHz for normal work JTAG_TDO_DELAY = 5 ; 0, 5, 10, 15 or AUTO TRST_TYPE = OPENDRAIN ; type of TRST output: OPENDRAIN or PUSHPULL RESET_TIME = 20 ; lenght of RESET pulse in ms; 0 means no RESET CORE0 = ARM926E, 2, 0x7926041 ; TAP is ARM926ejs CPU CORE0_BREAKMODE = soft ; breakpoint mode CORE0_INIT = INIT_mDDR ; init section for the CPU CORE0_FLASH0 = FLASH_NAND_BOOT ; flash section parameters CORE0_ENDIAN = LITTLE ; core is little endian ; workspace in DDR2 ;CORE0_WORKSPACE_ADDR = 0x80000000 ; start address of workspace for flash programmer ;CORE0_WORKSPACE_LEN = 0x10000 ; length of workspace in bytes ; workspace in internal RAM CORE0_WORKSPACE_ADDR = 0x78000000 ; start address of workspace for flash programmer CORE0_WORKSPACE_LEN = 0x10000 ; length of workspace in bytes CORE0_STARTUP_MODE = RESET ; or RUN CORE0_VECTOR_CATCH_MASK = 0 ; Default path to be used if only a file name (without the full path) is ; provided to a PEEDI command or for the FILE parameter in the Flash sections ; Examples: ; In a console: ; "flash prog tftp://192.168.3.1/image.elf" ; is equal to ; "flash prog image.elf" ; ; In a Flash Profile: ; FILE="tftp://192.168.3.1/image.bin", BIN, 0 ; is equal to ; FILE="image.bin", BIN, 0 ; CORE0_PATH = "tftp://192.168.3.1" ;CORE0_PATH = "card://" CORE0_FILE = "test.bin", BIN, 0xA0000000 [INIT_mDDR] memory write32 0x53F80008 0x50800000 ; MPCTL clock set memory write32 0x53F80064 0x00000000 ; AHB clock source for PER clocks memory write32 0xB8001010 0x00000004 ; Enble Mobile DDR memory write32 0xB8001000 0x92100000 ; Precharge Mode memory write32 0x80000400 0x12344321 memory write32 0xB8001000 0xA2100000 ; Autorefresh Mode memory write32 0x80000000 0x12344321 ; Two refresh dummy writes memory write32 0x80000000 0x12344321 memory write32 0xB8001000 0xB2100000 ; Enable CS0 Load Mode memory write32 0x80000033 0x00000012 ; Load mode dummy write memory write8 0x81000000 0x34 ; Extended Mode reister dummy write memory write32 0xB8001000 0x83216880 ; Normal mode 128Mb memory write32 0xB8001004 0x00295729 ; Configure mDDR delays memory write32 0x80000000 0x12344321 [FLASH_NAND_BOOT] CHIP = NAND_FLASH CPU = iMX25 ADDR_BASE = 0 FILE = "tftp://192.168.3.1/redboot.bin", 0x0000000 ;BAD_BLOCKS = 2819, 3067, 3071, 3585 ERASE_BAD_BLOCKS = NO OOB_INFO = IMX_ECC [SERIAL] ; serial port configuration BAUD = 115200 STOP_BITS = 1 PARITY = NONE TCP_PORT = 0 [TELNET] PROMPT = "mx25> " ; telnet prompt ;BACKSPACE = 127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 25 ; zummer volume