;-------------------------------------------------------------------------- ; ; ; PEEDI sample target configuration file ; ; Ronetix ; ; Supported devices : OMAP5912 ; ; Revision : 1.1 ; ; Date : March 4, 2008 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2010, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE=eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = ARM [PLATFORM_ARM] JTAG_CHAIN = 8, 4, 38 ; list of IR lenghts of all TAP controller in JTAG chain JTAG_CLOCK = 100, 4000 ; JTAG Clock in [kHz] - 5kHz jtag clock for init operations and 10MHz for normal work ; Valid range: 5 - 33000 TRST_TYPE = PUSHPULL ; type of TRST output: OPENDRAIN or PUSHPULL RESET_TIME = 100 ; lenght of RESET pulse in ms; 0 means no RESET TIME_AFTER_RESET = 200 CORE0 = DAVINCI, 1 ; TAP 0 is ARM926E CPU CORE0_STARTUP_MODE = RESET ; startup mode after reset: ; if RESET than no code is executed after reset ; if STOP,XX then the target executes code for XX period in ms. ; if RUN then the target executes code until stopped by the telnet "halt" command CORE0_BREAKMODE = soft ; default breakpoint mode for the debugger: ; soft - use software breakpoints ; hard - use hardware breakpoints CORE_BREAK_PATTERN = 0xDFFFDFFF ; software breakpoint pattern CORE0_INIT = INIT_OMAP ; init section CORE0_FLASH0 = U-BOOT CORE0_ENDIAN = little CORE0_WORKSPACE_ADDR = 0xA0001000 ; start address of workspace for flash programmer CORE0_WORKSPACE_LEN = 0x10000 ; length of workspace in bytes CORE0_PATH = "tftp://192.168.3.1" ; default path ;CORE0_PATH = "card://" ; default path CORE0_FILE = "test.bin", BIN, 0xA0000000 [INIT_OMAP] mem write16 0xFFFEC808 0x00F5 ; Disable Watchdog Timer mem write16 0xFFFEC808 0x00A0 ; [U-BOOT] CHIP = S29WS256N ACCESS_METHOD = AGENT CHECK_ID = YES CHIP_WIDTH = 16 CHIP_COUNT = 1 BASE_ADDR = 0x00000000 FILE="card:u-boot.bin", BIN, 0xC0000000 AUTO_ERASE=YES [SERIAL] BAUD=115200 STOP_BITS=1 PARITY=NONE TCP_PORT = 0 ; 2023 [TELNET] PROMPT = "omap> " ; telnet prompt ;BACKSPACE=127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 25 ; beeper volume [ACTIONS] ; user defined scripts ;AUTORUN = 2 ; executed on every target connect 1 = erase 2 = prog 3 = dump_ram [erase] ; erase flash flash erase [prog] ; program flash flash prog [dump_ram] ; dump part of RAM memory dump 0x20000000 0x0100 card:ram.bin