;-------------------------------------------------------------------------- ; ; ; PEEDI sample target configuration file ; ; Ronetix ; ; Supported devices : Analog Devices ADSP-BF533 ; Board : Blutechnix CM-BF533 ; ; Revision : 1.3 ; ; Date : June 11, 2010 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2010, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE=eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = BLACKFIN ; platform is BLACKFIN [PLATFORM_BLACKFIN] JTAG_CHAIN = 5 ; list of IR lenght of all TAP controller in JTAG chain JTAG_CLOCK = 10, 25000 ; JTAG Clock in [kHz] - 10kHz jtag clock for init operations and 25MHz for normal work JTAG_TDO_DELAY = 5 ; auto tune JTAG TRST_TYPE = PUSHPULL ; type of TRST output: OPENDRAIN or PUSHPULL CORE0 = BF533 ; TAP is BF533 CPU CORE0_STARTUP_MODE = reset CORE0_BREAKMODE = soft ; breakpoint mode: ; soft - software breakpiont ; hard - use hardware breakpoints instead of software CORE0_INIT = INIT_BF533 ; init section for the board CORE0_FLASH0 = NOR_FLASH ; flash section parameters CORE0_ENDIAN = LITTLE ; core is little endian CORE0_WORKSPACE = 0xFFA00000, 0x4000 ; start address and length in bytes for agent code CORE0_DATASPACE = 0xFF800000, 0x4000 ; start address and length in bytes for agent data CORE0_FILE = "myfile.bin", BIN, 0 ; default file CORE0_PATH = "tftp://192.168.3.1" ; default path [INIT_BF533] ; Configure SCLK & CCLK Dividers mem write16 0xFFC00004 3 ; set PLL mem write16 0xFFC00010 0x300 mem write16 0xFFC00000 0x2800 ; init SDRAM at address 0x0 mem write16 0xFFC00A18 0x081C mem write16 0xFFC00A14 0x0011 mem write 0xFFC00A10 0x00911149 [NOR_FLASH] CHIP = CFI_FLASH ; flash chip ACCESS_METHOD = AGENT ; program method BASE_ADDR = 0x20000000 ; chip is mapped at 0x20000000 FILE = "test256k.bin" BIN 0x20000000 AUTO_ERASE = NO ; erase before program [SERIAL] ; serial port configuration BAUD = 115200 STOP_BITS = 1 PARITY = NONE TCP_PORT = 0 ;TCP_PORT = 2023 [TELNET] PROMPT = "bf533> " ; telnet prompt ;BACKSPACE = 127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 25 ; zummer volume [ACTIONS] ; user defined scripts ;AUTORUN = 2 ; executed on every target connect 1 = erase 2 = prog 3 = dump_ram 4 = dump_flash [erase] ; erase flash flash erase [prog] ; program flash flash prog [dump_ram] ; dump part of RAM memory dump 0x00000000 0x01000 tftp://192.168.1.1/ram.bin [dump_flash] ; dump part of FLASH memory dump 0x20000000 0x10000 tftp://192.168.1.1/flash.bin