Starting RedBoot v20.12.1 ...
Platform: PEEDI
FLASH TC58FVB160A: 0x05800000-0x059fffff, 32 x 0x10000 blocks

*** INFO: to enter RedBoot restart while holding both buttons pressed ***

== Executing boot script
RedBoot> fis load peedi; go
Please wait...
+++++

Network:
  IP address         : 192.168.3.101
  Subnet mask        : 255.255.255.0
  Gateway            : 192.168.3.10
  Domain Name        : office
  MAC address        : 02:00:0b:6b:30:1f


PEEDI - Powerful Embedded Ethernet Debug Interface
Copyright (c) 2005-2021 www.ronetix.at - All rights reserved
Hw:1.2, Fw:21.5.7, SN: PD-0000-0B6B-301F
------------------------------------------------------------

peedi>
++ info: opening file 'tftp://192.168.3.60/ls1043a.cfg'
++ info: loading file 'tftp://192.168.3.60/ls1043a.cfg'...
++ info: done, loaded 1467 meaningful bytes.
++ info: opening file 'eep:license.txt'
++ info: loading file 'eep:license.txt'...
++ info: done, loaded 534 meaningful bytes.

++ info: Target Vref = 1.72V
++ info: Wakeup 20 ms
++ info: RESET and TRST asserted
++ info: TRST released
++ info: RESET released
++ info: wait 20 ms
++ info: reset type: LS1043A
++ info: Overriding RCW source with 0x9F
++ info: RESET asserted
++ info: RESET released
++ info: wait 20 ms
++ info: BYPASS check passed, 2 TAP controller(s) detected
++ info: TAP 0 : IDCODE = 0x06B1001D, Freescale LS1043A SAP
++ info: TAP 1 : IDCODE = 0x5BA00477, LS1000_x64
++ info: core 0: requesting Debug and System power-up (CDBGPWRUPREQ, CSYSPWRUPREQ)
++ info: core 0: Found Access Port 0 (IDR=0x24770004) - MEM-AP AXI
++ info: core 0: Found Access Port 1 (IDR=0x44770002) - MEM-AP APB
++ info: core 0: using APB port 1
++ info: core 0: using AHB port 0

ls1043a>
++ info: core 0: CoreSight Debug component set at 0x80410000
++ info: core 0: CrossTrigger    component set at 0x80420000
++ info: core 0: Found VFP and NEON features
++ info: core 0: stopped by user request, PC=0x00000000000000F8, CPSR=0x000003CD
++ info: core 0: Cortex-A53, CPUID = 0x410FD034
++ info: core 0: connected
++ info: core 0: initialized

ls1043a>

ls1043a> flash info
MMC/SD/eMMC configuration for core #0:
    Product:   SA08G
    Size:      7592 MB (15548416 blocks)
    Type:      SD(HC) v2.0
    Clock:     50000 kHz
    Bus width: 4-bit

FLASH commands default parameters:
  flash read   0x00000000 0x00ED4000
  flash blank  0x00000000 0x00ED4000
  flash erase  0x00000000 0x00ED4000
  flash lock   0x00000000 0x00ED4000
  flash unlock 0x00000000 0x00ED4000
  flash query  0x00000000 0x00ED4000
  flash program test256k.bin bin 0x00000002
  flash verify  test256k.bin bin 0x00000002
ls1043a>
ls1043a>
ls1043a> flash set 1
Selected FLASH section: FLASH_NOR
ls1043a> flash info

CORE #0, FLASH #1 -> FLASH_NOR
  1x16-bit CFI NOR Intel, ID: 0x227E, total 128 MB at address 0x60000000
  Vendor ID = 0x89, Device ID = 0x227E
  Write buffer size: 1024 bytes
  Block erase timeout: 768 ms
  Chip  erase timeout: 786 s
  Programming method: DIRECT
  Auto lock after program: no
  Auto erase : no

FLASH commands default parameters:
  flash read   0x60000000 0x08000000
  flash blank  0x60000000 0x08000000
  flash erase  0x60000000 0x08000000
  flash lock   0x60000000 0x08000000
  flash unlock 0x60000000 0x08000000
  flash query  0x60000000 0x08000000
  flash program test32k.bin bin 0x67FE0000
  flash verify  test32k.bin bin 0x67FE0000
ls1043a>

ls1043a> memory test
++ info: testing 0x10000000, length 0x20000

writing 32-bit pattern ..
reading 32-bit pattern ... .passed.
8/16-bit memory access ... passed.
++ info: successfully checked 128 KB in 0.96 sec