;-------------------------------------------------------------------------- ; ; ; PEEDI sample target configuration file ; ; Ronetix GmbH ; ; Supported devices : AM4378 ; Supported board : Embest SBC-EC8800 ; ; Revision : 1.0 ; ; Date : April 17, 2019 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2012, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE = eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = CORTEX ; platform is Cortex [PLATFORM_CORTEX] JTAG_CHAIN = 6, 4 ; list of TAP controllers in the JTAG chain JTAG_CLOCK = 5000 ; JTAG Clock in [kHz] TRST_TYPE = PUSHPULL ; type of TRST output: OPENDRAIN or PUSHPULL RESET_TIME = 20 ; length of RESET pulse in ms; 0 means no RESET RESET_TYPE = ICEPICK-D, 12, 1 ; enable TAP12, warm reset TIME_AFTER_RESET = 200 CORE0 = CORTEX-A, 1, 0x3BA00477 CORE0_APSEL = 1 CORE0_DEBUG_ADDR = 0x80000000, 0x80008000 CORE0_STARTUP_MODE = RESET ; stop the core immediately after reset CORE0_ENDIAN = LITTLE ; core is little endian CORE0_BREAKMODE = SOFT ; breakpoint mode CORE0_INIT = INIT_AM4378 ;CORE0_INIT = INIT_LINUX ; init section with working U-BOOT CORE0_WORKSPACE = 0x40300000, 0xE000 ; address, lenght in bytes CORE0_FLASH0 = MMC_CARD CORE0_PATH = "tftp://192.168.3.60" CORE0_FILE = "test.bin", BIN, 0x20000000 [INIT_LINUX] break add hard 0xc0008958 ; kernel break address got by 'nm vmlinux | grep start_kernel' go wait 60000 stop break del all beep 100 100 [INIT_AM4378] ; disable watchdog mem write 0x44E35048 0xAAAA wait 2 mem write 0x44E35048 0x5555 wait 2 ; 17.04.2019 - eMMC programming doesn't work [MMC_CARD] CHIP = CARD CPU = OMAP4 SDHC = 1 FILE = "test32k.bin", bin, 2 PARTITION = 0 [SERIAL] ; serial port configuration BAUD = 115200 STOP_BITS = 1 PARITY = NONE TCP_PORT = 0 [TELNET] PROMPT = "am43xx> " ; telnet prompt ;BACKSPACE = 127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 25 ; beeper volume [ACTIONS] ; user defined scripts ;AUTORUN = 1 ; executed on every target connect 1 = prog [prog] ; program flash flash set 0 flash erase flash prog