;-------------------------------------------------------------------------- ; ; ; PEEDI target configuration file for PXA270 processor ; ; Ronetix ; ; Supported devices : PXA270 ; Board : Custom board with OneNAND Flash ; ; Revision : 1.5 ; ; Date : October 22, 2008 ; ; The file is delivered "AS IS" without warranty or condition of any ; kind, either express, implied or statutory. This includes without ; limitation any warranty or condition with respect to merchantability or ; fitness for any particular purpose, or against the infringements of ; intellectual property rights of others. ; ;-------------------------------------------------------------------------- ;-------------------------------------------------------------------------- ; The following section contains licenses that are required for PEEDI to ; operate. These licenses must be filled before using this file. ; The [LICENSE] section may contain license keys for one or more PEEDIs. ; ; Example: ; [LICENSE] ; KEY = UPDATE_24MAY2010, 1111-1111-1111-1 ; KEY = XXXXX, 2222-2222-2222-2 ; ; The [LICENSE] section may point to an external file which contains ; license keys for one or more PEEDIs. The external file must include ; the text [LICENSE] followed by all keys. ; ; Example: ; [LICENSE] ; FILE = tftp://192.168.3.1/license.txt ; or ; FILE=eep:license.txt ; or ; FILE = ftp://user:password@192.168.3.1/license.txt ; ; ; PEEDI is shipped with license keys stored in "eep:license.txt" and ; printed on a label on the bottom side of PEEDI. ; [LICENSE] FILE=eep:license.txt ;-------------------------------------------------------------------------- [DEBUGGER] PROTOCOL = gdb_remote ; gdb remote REMOTE_PORT = 2000 ; TCP/IP port [TARGET] PLATFORM = XScale ; platform is XScale [PLATFORM_XSCALE] JTAG_CHAIN = 7 ; list of IR length of all TAP controller in JTAG chain JTAG_CLOCK = 1000, 16000 ; JTAG Clock in [kHz] - 1MHz JTAG clock for init ; operations and 16MHz for normal work TRST_TYPE = PUSHPULL ; type of TRST output: OPENDRAIN or PUSHPULL RESET_TIME = 20 ; length of RESET pulse in ms; 0 means no RESET TIME_AFTER_RESET = 500 CORE0 = XScale, 0 ; TAP is XSCALE CPU CORE0_STARTUP_MODE = RESET ; Stop core CORE0_BREAKMODE = soft ; breakpoint mode: soft or hard CORE0_INIT = INIT_BOARD ; init section CORE0_FLASH0 = FLASH_ONENAND ; flash section parameters CORE0_ENDIAN = LITTLE ; core is little endian CORE0_WORKSPACE_ADDR = 0xA0001000 ; start address of workspace for ; flash programmer CORE0_WORKSPACE_LEN = 0x10000 ; length of workspace in bytes CORE0_DEBUG_HANDLER_ADDR= 0xFE000000 ; debug handler base address CORE0_VECTOR_CATCH_MASK = 0x0 ; 0x10 catch data abort exceptions CORE0_VECTOR_UNDEF = AUTO CORE0_VECTOR_SWI = AUTO CORE0_VECTOR_PABORT = AUTO CORE0_VECTOR_DABORT = AUTO CORE0_VECTOR_RES = AUTO CORE0_VECTOR_IRQ = AUTO CORE0_VECTOR_FIQ = AUTO CORE0_RELOCATED_UNDEF = AUTO CORE0_RELOCATED_SWI = AUTO CORE0_RELOCATED_PABORT = AUTO CORE0_RELOCATED_DABORT = AUTO CORE0_RELOCATED_RES = AUTO CORE0_RELOCATED_IRQ = AUTO CORE0_RELOCATED_FIQ = AUTO ; Default path to be used if only a file name (without the full path) is ; provided to a PEEDI command or for the FILE parameter in the Flash sections ; Examples: ; In a console: ; "flash prog tftp://192.168.3.1/image.elf" ; is equal to ; "flash prog image.elf" ; ; In a Flash Profile: ; FILE="tftp://192.168.3.1/image.bin", BIN, 0 ; is equal to ; FILE="image.bin", BIN, 0 ; CORE0_PATH = "tftp://192.168.3.1" ;CORE0_PATH = "card://" [INIT_LINUX] break add watch 0xffff001C w 32 ; break after vectors are set go ; start target wait 30000 stop ; wait to break go ; start again with updated vectors [INIT_BOARD] memory write 0x48000008 0x000095F9 ; MSC0 = 0x000095F9 memory read 0x48000008 ; read MSC0 memory write 0x4800000C 0x0000F974 ; MSC1 = 0x0000F974 memory read 0x4800000C ; read MSC1 memory write 0x48000010 0x00000000 ; MSC2 = 0x00000000 memory read 0x48000010 ; read MSC2 memory write 0x48000014 0x00000001 ; MECR = 0x00000001 memory read 0x48000014 ; read MECR memory write 0x48000004 0x20CA601E ; MDREFR = 0x0000001E memory read 0x48000004 ; read MDREFR memory write 0x4800001C 0x40044004 ; SXCNFG = 0x40044004 memory write 0x48000004 0x2043601E ; MDREFR = 0x0000001E memory read 0x48000004 ; read MDREFR memory write 0x48000004 0x2003601E ; MDREFR = 0x0000001E memory read 0x48000004 ; read MDREFR memory write 0x48000004 0x2003E01E ; MDREFR = 0x0000001E memory read 0x48000004 ; read MDREFR memory write 0x48000000 0x08000AC8 ; MDCNFG = 0x08000AC8 memory read 0x48000000 ; read MDCNFG wait 300 memory write 0x48000000 0x08000AC9 ; MDCNFG = 0x08000ACD memory read 0x48000000 ; read MDCNFG memory write 0x48000040 0x00000000 ; MDMRS = 0x00000000 memory read 0x48000040 ; read MDCNFG memory write 0x48000004 0x2013E01E ; MDREFR = 0x0000001E memory read 0x48000004 ; read MDREFR memory write 0x4800004C 0xFFFFFFFF ; BSCNTR0 = 0xFFFFFFFF memory write 0x48000050 0xFFFFFF5F ; BSCNTR1 = 0xFFFFFF5F memory write 0x4800005C 0xFFFFFFFF ; BSCNTR2 = 0xFFFFFFFF memory write 0x48000060 0xFFFFFFFF ; BSCNTR3 = 0xFFFFFFFF [FLASH_ONENAND] CHIP = ONENAND ; flash chip BASE_ADDR = 0x0000000 ; chip is mapped at 0x0000000 FILE = "u-boot.bin", BIN, 0 ; file to program ERASE_BAD_BLOCKS = NO OOB_INFO = ONENAND ; use built-in OneNAND ECC engine [SERIAL] ; serial port configuration BAUD = 115200 STOP_BITS = 1 PARITY = NONE TCP_PORT = 0 ; enable CLI over RS232 ;TCP_PORT = 2023 ; enable serial over TCP/IP [TELNET] PROMPT = "PXA270> " ; telnet prompt ;BACKSPACE = 127 ; comment out for autodetect [DISPLAY] BRIGHTNESS = 20 ; LED indicator brightness VOLUME = 25 ; beeper volume [ACTIONS] ; user defined scripts ;AUTORUN = 2 ; executed on every target connect 1 = erase 2 = prog [erase] ; erase flash flash erase [prog] ; program flash flash program